Products & Applications
Empower the development of the industry with chemical technology and build a healthy industrial ecological chain.
Mine
Mextral® 3938H
It’s designed for the extraction of lithium from other alkalis after earth alkalis, for example magnesium and calcium, are removed.
Mextral® 3939H
It has less water solubility and better stability, whose lithium extraction is performed in neutral aqueous solutions, which can decrease the operating cost of the SX plant, mainly applied to the special extraction of low concentration lithium in the waste solutions.
Famigo® FS-101
It is a fairly stable fluorocarbon, which is directly used in the electrowinning solution. By reducing the surface tension of the electrowinning solution, it suppresses the generation of acid mist, improves the air quality of the electrowinning workshop, provides occupational health protection, and increase the service life of the equipment. It is mainly used in the electrowinning section of copper hydrometallurgy, and can be used with floating plastic pellets. It will not produce large amount of foam on the surface of the electrowinning solution, avoids the loss of acid mist suppressant, and does not have any adverse effects on the solvent extraction and electrowinning process.
Flotilla® 103
It is a chelating collector, suitable for oxide minerals such as scheelite, stannite, fluorite and ilmenite. The selectivity is the same as that of conventional sodium alkyl hydroxamate, but the collecting ability is improved, and the foam is not viscous and easy to defoam.
Flotilla® 102
It is a coal collector with strong collecting ability with low dosage, and high flash point (>160 ℃). It is not a dangerous chemical, safe and environmentally friendly to use.
Flotilla® 704
It is an efficient pyrite and pyrrhotite depressant for semi massive and massive sulfide ores, and can replace lime at low dosage, only 1/100-1/30 of lime, suitable pyrite depressant in low pH sulfide flotation.
Flotilla® 601
It is a frother and widely used in flotation with strong and stable froth.
Flotilla® 701
It is an efficient copper depressant in Cu-Mo separation, which could replace ~40% of sodium sulfide or sodium thioglycolate. It does not affect the collection of molybdenum, and it is a non-hazardous chemical.
Flotilla® 703
It is an efficient depressant in Cu-Pb separation, which could replace dichromate. Basically it does not affect the collection of copper, and it is a non-hazardous chemical.
Flotilla® 402
It is a novel and environmentally friendly thiocarbamate collector with superior selectivity for pyrite, suitable for low pH flotation and can reduce the dosage of lime, having a strong ability to collect copper sulfide with low dosage.
Flotilla® 501
It is a white crystal and suitable collector for galena flotation at high pH, and collecting ability is stronger than xanthate and DTP with faster flotation kinetics and higher selectivity.
Flotilla® 303
It is an effective collector for gold, silver, copper and zinc sulfide minerals with low collecting ability for pyrite in alkaline circuit. It only has very weak foaming properties.
Flotilla® 304
It is a new and high-efficiency collector for gold, silver, copper and zinc sulfide minerals with low collecting ability for pyrite in alkaline circuit, having weak foaming properties.
Flotilla® 401
It is an excellent collector for sphalerite, galena and chalcopyrite minerals with high selectivity and special separation efficiency.
Flotilla® 106
Carboxylic collector is used in flotation of oxide minerals such as fluorite, phosphate, etc. with higher selectivity.
Flotilla® 201
It is widely used in flotation of easy-to-process sulfide minerals and differential flotation of complex sulfide minerals, also can be used as precipitant in hydro-metallurgy and vulcanizing accelerator of rubber.
Flotilla® 105
Molybdenum collector shows higher Mo recovery (2-4% recovery increase) with high flash point. It is not a dangerous chemical, safe to store and ship than conventional diesel collector.
Mextral® DT100
It is a special diluent for extraction, which can effectively improve the physical properties of the organic phase, reduce the viscosity of the organic phase, and improve the phase separation effect. It is environmentally friendly and non-toxic, a special diluent for extraction with excellent comprehensive indexes.
Mextral® 272P
It has a good Co/Ni separation coefficient, and is often used for Co/Ni extraction and separation; it can also be used for the extraction of rare earth, molybdenum, etc.
Mextral® 336A
It is widely used in the extraction of cadmium, cobalt, hafnium, iron, niobium, tungsten, uranium, vanadium, zinc, or the extraction of organic or inorganic acids such as bisphenol A, amino acids, p-aminobenzene sulfonic acid, etc. from industrial wastewater, production of various anionic oil-soluble salts and intermediates for the preparation of surfactants, dyes, pigments, etc. This extractant can extract a variety of complex anions, so it can be applied to the extraction and separation of tungsten, molybdenum, vanadium, sulfuric acid, phosphoric acid, arsenate, etc.
Mextral® 20PP
It can be used for extraction and separation of nickel and cobalt and rare earth elements, zinc, molybdenum, indium, germanium, gallium, etc. and is also commonly used for removal of impurities before nickel and cobalt extraction. It has stable performance in use. It is an industrial extractant widely used in rare earth element separation and nonferrous metal extraction.
Mextral® 50PP
It can be used for extraction and separation of cobalt and nickel; extraction of rare earth metals and non-ferrous metals such as indium, rhodium and vanadium; extraction of zirconium and hafnium in hydrochloric acid medium.
Mextral® V10
It can be used for the extraction of copper, cobalt, nickel, zinc, cesium, rare earth and other metals, and can also form a synergistic extraction system with other extractants to improve the separation coefficient and extraction rate between metal ions.
Mextral® 6104H
It can be used for the separation of cobalt, nickel and impurities such as calcium, magnesium and manganese. It has good cobalt and nickel stripping performance, simplifies the separation process, and can obtain high-purity nickel and cobalt products. It is a new generation of nickel and cobalt special extractant.
Mextral® 6103H
It can be used to extract cobalt, nickel, zinc, germanium, molybdenum, uranium and other metals. It has the advantages of fast extraction kinetics, good selectivity, fast phase separation and less entrainment. It can significantly improve the separation coefficient of cobalt, zinc with calcium, manganese and magnesium.
Mextral® 63H
It can be used to extract nickel, cobalt, zinc, germanium, molybdenum, uranium and other metals. As a kinetic additive and synergistic extractant for other chelating extractants, it has the advantages of high extraction efficiency, fast extraction kinetics, and can significantly improve the separation coefficient of nickel, cobalt, zinc with calcium, manganese, and magnesium.
Mextral® 54-100
The extractant has the characteristics of low viscosity, large extraction capacity and easy stripping. It is suitable for the extraction of copper under ammonia conditions. It can effectively extract copper from mine ammonia leaching solution and alkaline etching solution of circuit board, which has good environmental protection and economic benefits.
Mextral® CLX50
It is suitable for the extraction of copper and palladium in chloride solutions. The extraction efficiency is independent of the pH value of the feed solution. It is especially suitable for the extraction of copper in acidic etching solution. It can be stripped with water, and has the advantages of high stripping efficiency, less loss of extractant, and good phase separation.
Mextral® AN-200
It is a special anti-nitrification extractant with stable performance. It can be applied to the extraction of copper from mine acid leaching solution, especially suitable for the extraction of copper from leaching solution containing nitrate under the condition of medium-high pH conditions.
Mextral® AN-100
It is a special anti-nitrification extractant with stable performance. It can be applied to the extraction of copper from mine acid leaching solution, especially suitable for the extraction of copper from leaching solution containing nitrate under the condition of medium-low pH conditions.
Mextral® 5050H
Strong extraction capacity and good Cu/Fe selectivity, it can be applied to the extraction of copper from mine acid leaching solution, and is more suitable for copper extraction under medium-low pH conditions.
Mextral® 5887H
With excellent anti-oxidation capacity, it is used to extract copper from acidic solutions containing oxidizing substances, reducing the loss of extractants and prolonging service life.
Mextral® 9890H
It has good stability in use, and strong net copper transfer capacity. It can be used to extract and separate copper from mine acid leaching solution, and is more suitable for copper extraction under medium pH conditions.
Mextral® 5850H
It has good extraction effect, fast phase separation, less entrainment, high Cu/Fe selectivity, and good stability. As the special extractant for copper, it is mainly used for the extraction of copper from the mine acid leaching solution and electroplating waste solution. It is more suitable for copper extraction under medium pH conditions.
Mextral® 5540H
It has the advantages of fast extraction kinetics, good phase separation, high Cu/Fe selectivity, strong copper transfer ability, and good stability in use. It can be used for copper extraction from mine acid leaching solution and suitable for copper extraction under medium-low pH conditions.
Mextral® 5530H
Strong extraction capacity, fast extraction kinetics, good phase separation, and Cu/Fe selectivity. It can be used for copper extraction from mine acid leaching solution, and is suitable for medium-low pH feed solution.
Mextral® 5510H
It has the advantages of strong extraction capacity, good stripping performance, high copper transfer rate, good stability, high Cu/Fe selectivity, less organic phase loss, low aqueous phase entrainment. It is suitable for copper extraction under medium acidity.
Mextral® 5520H
Good extraction effect, fast extraction kinetics, good stability, fast phase separation. It is suitable for copper extraction under medium-low pH conditions.
Mextral® 9790H
It combines the advantages of high extraction efficiency and high stripping efficiency, with good stability and strong net copper transfer capacity. It is widely used for the extraction of copper from mine acid leaching solution, and more suitable for the extraction of copper under the medium-high pH conditions.
Mextral® 622H
It can form water-insoluble complex with copper ions and is mainly used for the extraction of copper in acidic medium. It has stable performance in use, high Cu/Fe selectivity, and is suitable for copper extraction under medium-low pH conditions.
Mextral® 5910H
Stable performance in use, high Cu/Fe selectivity, fast phase separation, less entrainment, strong copper transfer ability, It is widely used in the extraction of copper from mine acid leaching solution, especially suitable for medium-low concentration feed solution and leaching solution with low acidity.
Mextral® 5774H
Good extraction effect, fast phase separation, less entrainment, high net copper transfer, good extraction performance under medium pH conditions, high Cu/Fe selectivity. It is widely used for the extraction of copper from mine leaching solution.
Mextral® 5640H
It has high Cu/Fe selectivity, strong extraction ability, stable performance, fast phase separation and less entrainment. It is a special extractant for copper and is widely used in the extraction of copper from acid leaching solutions of copper mines. It is more suitable for copper extraction under medium-low pH conditions.
Mextral® 860H-IC
It is a strong copper extractant, capable of extracting copper at lower pH. It can also be used to extract zinc from ammoniacal solutions. Used in conjunction with Mextral 84H or Mextral 84-IC, it can meet the needs of copper extraction from various leaching solutions.
Mextral® 84-IC
It has good stability, strong copper transfer ability, and easy to strip. Used in conjunction with Mextral860H or Mextral860H-IC, it can meet the needs of copper extraction from various leaching solutions. It can also be used to extract metals such as nickel and zinc, and is more suitable for the extraction of copper under higher pH conditions.
Mextral® 984H-C
It is widely used for copper extraction from mine acid leaching solution and electroplating sludge leaching solution, and also for copper recovery from industrial wastewater. It is more suitable for the extraction of copper under medium pH conditions.
Mextral® 860H
As the copper extractant with strong extraction ability, it is especially suitable for extracting copper at low Ph. Used in conjunction with Mextral 84-IC or Mextral 84H, it can meet the needs of copper extraction from various leaching solutions.
Mextral® 84H
It is mainly used for the extraction of non-ferrous metals such as copper and nickel. It has the advantages of high stripping efficiency, low stripping acidity, large copper transfer, and good stability in use.
Mextral® 973H
It has strong extraction ability, good Cu/Fe selectivity, and fast phase separation. It has the advantages of strong extraction ability and good stripping performance, and is more suitable for copper extraction under medium-low pH conditions.
Mextral® 984H
It is a high-efficiency copper extractant with good stability. It has the advantages of strong extraction ability, good stripping performance, and strong transfer ability of net copper. It is more suitable for copper extraction under moderate acidity conditions.
©️ 2023 KopperChem All Rights Reserved.
渝公网安备50011502000737号